Understanding Plumbing Basics When Installing a Bathtub
Understanding Plumbing Basics When Installing a Bathtub
Blog Article
The writer is making a few great observations relating to How to Install a Bathtub Yourself overall in the article underneath.
Mounting a bathtub isn't specifically brain surgery, however it does require solid plumbing, carpentry, and also often, tiling skills. Changing an old bath tub with a brand-new one is likewise a moderately challenging job. If the old bathtub is conveniently available, the project can move quickly; if you have to open up a wall to eliminate the old bathtub and also place the new bath tub, the task is a lot harder. In either instance, the project is within a house handyman's skills, although you will require a helper to move out the old tub and also embeded in the brand-new one. Make sure you have certified on your own for the job as well as fit trying it. Rather than employing a contractor to take over a halfway-completed job, it is much better to take into consideration using one before you start. Opportunities are you might require a professional plumber to make tube connections.
This short article will aid you install a brand-new bath tub in your shower room if you have actually already acquired a new bathtub and also do not require to transform the plan of your previous water pipelines.
Your devices and also product checklist ought to make up the following:
Preparing for the Installment
Firstly, the sustaining structure supplied with the bathroom ought to be fitted (if required) according to the supplier's instructions. Next off, fit the taps or mixer to the bath tub. When suitable the faucet block, it is important to make sure that if the tap features a plastic washing machine, it is fitted between the bathroom and also the faucets. On a plastic bathroom, it is also sensible to fit a supporting plate under the faucets unit to avoid pressure on the bathtub.
Fit the adaptable tap ports to the bottom of the two taps utilizing 2 nuts as well as olives (often provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet through the hole in the bathroom. Make use of the nut provided by the producer to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the flexible overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bath. Make certain you utilize every one of the supplied washing machines.
Connect the catch to the bottom of the waste outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Connect all-time low of the overflow tube in a comparable manner.The bath need to now be ready to be fitted in its last position.
Removing Old Taps
If you need to change old faucets with brand-new ones as a part of your setup, after that the first thing you need to do is separate the supply of water. After doing so, switch on the faucets to drain pipes any kind of water remaining in the system. The process of removing the existing taps can be quite troublesome because of the restricted access that is frequently the case.
Use a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that links the supply pipelines to the taps. Have a towel all set for the staying water that will certainly come from the pipelines. Once the supply pipes have been eliminated, utilize the same tool to loosen up the nut that holds the taps onto the bath/basin. You will need to quit the single taps from turning during this procedure. As soon as the faucets have actually been gotten rid of, the holes in the bath/basin will certainly need to be cleaned up of any kind of old securing compound.
Prior to moving on to fit the new taps, contrast the pipe connections on the old faucets to the new faucets. If the old faucets are longer than the brand-new taps, after that a shank adapter is needed for the brand-new taps to fit.
Setting up the Bathtub
Making use of both wooden boards under its feet, position the bathtub in the needed position. The wooden boards are handy in evenly spreading the weight of the bathtub over the area of the boards instead of focusing all the weight onto 4 tiny factors.
The following goal is to make sure that the bath tub is leveled all round. This can be attained by checking the level and also adjusting the feet on the bathtub till the level reviews degree.
To install taps, fit the bottom of the furthest flexible tap port to the proper supply pipeline by making a compression join; after that do the exact same for the other faucet.
Turn on the water system and examine all joints as well as new pipework for leakages and tighten them if essential. Fill up the bathtub as well as likewise examine the overflow outlet and also the normal electrical outlet for leaks.
Lastly, repair the bathroom paneling as described in the producer's user's manual. Tiling and sealing around the tub must wait up until the bath tub has been used at the very least when as this will settle it into its final setting.
Fitting New Taps
If the tails of the new taps are plastic, then you will need a plastic connector to prevent damage to the thread. One end of the port fits on the plastic tail of the faucet as well as the other end offers a connection to the existent supply pipes.
If you need to fit a monobloc, after that you will call for lowering couplers, which attaches the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next off, position the tap in the placing hole in the bath/basin guaranteeing that the washers remain in location between the faucet and the sink. Safeguard the faucet in place with the manufacturer given backnut. When the faucet is safely in position, the supply pipes can be attached to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with typical tap adapters. The previous type needs to be attached to the faucet finishes initially, tightening only by hand. The supply pipelines can later on be attached to the other end. Tighten up both ends with a spanner after both ends have actually been attached.
Tiling Around the Tub
In the location where the bathroom fulfills the tile, it is required to seal the joins with a silicone rubber caulking. This is necessary as the installation can relocate enough to crack a rigid seal, causing the water to penetrate the wall in between the bathroom as well as the tiling, causing complications with wetness as well as possible leaks to the ceiling listed below.
You can select from a range of coloured sealants to assimilate your components and also installations. They are offered in tubes and cartridges, and can sealing gaps approximately a size of 3mm (1/8 inch). If you have a larger gap to fill, you can load it with twists of drenched newspaper or soft rope. Remember to constantly fill the bath tub with water prior to sealing, to enable the activity experienced when the bathtub is in usage. The sealant can split fairly early if you do not think about this motion before securing.
Conversely, ceramic coving or quadrant floor tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are also conveniently available on the marketplace. It is advisable to fit the ceramic tiles using water-resistant or water-proof adhesive as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We had been brought to that editorial about A Step-by-Step Guide to Installing a Bathtub through a good friend on our other site. Are you aware of somebody who is fascinated by the niche? Feel free to promote it. Thanks a lot for your time spent reading it.
Set An Appointment Report this page